Clik here to view.
953C track tension problem
My 953C track tensioner ram is rubbing the front roller on 1-side, needing advice on what is causing this and how to fix it. My undercarriage should be replaced anytime but I would like to run its...
View ArticleWhat does a fuel float tank do?
I have a Komatsu D75S-3 and am having problems getting fuel to the filter. Strainers clean at bottom of tank. I've had the float tank off and cleaned it. Not sure why I can't get fuel to filter?...
View ArticleClik here to view.
953LGP (20Z) with 3204, engine oil leak at hyd pump weep hole.
Eng oil has been leaking some at hyd pump weep hole for some time. This week, owner says there is a wash down from the hole, and machine is using about 1 gal per day, and oil is mixing with dust and...
View Article941 input shaft seal replacement
what will i have to do to replace the input shaft seal on the torque converter? it has been seeping since i have owned it,i figure from it sitting up and drying out before i bought it,but now it is...
View Article973 track pad interchange
I've acquired a 973. Always wanted one and a couple big lake jobs and a lot of brush seemed to be a good excuse. It has double grouser pads and I'd like to have single grousers like my 963 has. Looks...
View Article84 Case 350 1st gear lockout?
I recently picked up this loader for a pretty good deal ($1400) However it blew up a hydraulic hose when testing, and it needs a rebuild.. basically a bunch of easy things. My problem is that since...
View ArticleBalance shafts
Bought a Cat reman 3304 long block. Trying to get it back together. Need both balance shafts. Cat shafts are about $425 a piece. Looks like I can get after market for a little over $100. I don't want...
View Article289c2 caterpillar exclamation warning light and buzzer
Not showing any codes - saved code was e391-1 on control panel - turn key on and wait 5 sec and all Gage's go to zero and buzzing and exclamation yellow point comes up and ideas out there
View ArticleCase 450B problem
I bought a Case 450B track loader with a thrown rod, replaced engine, filters, most of the hydraulic hoses and it is running great. The problem is that the high/low range shifter is broken off below...
View ArticleClik here to view.
International 175C information
I just bought an old 175C loader to use on the farm. I'm looking for some information on it. The serial number is 4290004U003648* It has pedal steer instead of the levers. Does it also have a...
View ArticleIHC 175 B located in Brazil
Hello to everyone in this forum, there is an old crawler loader from Dresser on a construction´s yard here in Brazil. The machine rests there for more than 10 years without running, the owner says the...
View ArticleNew to me 955L
I chose this machine in part from lurking at the site over the past year or so. I checked out a few 955s and chose this one as the undercarriage is well maintained and the PO, a mechanic had spent...
View ArticleClik here to view.
941 Bucket Repairs
Now it's on to some bucket repairs where the back heel of the bucket has worn off. Have some new 1/2" plates cut & ready to go on once the old mess is gouged off. Attached Images
View Articlestiff clutch pedal
Hello, im a new member here and have a question, I picked up a john deere 355d track loader in decent condition, it has only been used maybe 10 hours in 5 plus years, the one issue im having is the...
View ArticleWhy track loaders?
I'm not trying to start an argument. I'm only trying to understand. I feel that track loaders were common at an earlier day than articulated wheel loaders. Why? A wheel loader is faster, costs less to...
View ArticleIH100E Idler arm
I'm a new user to the forum and just recently purchased a 1985 IH 100e Track loader. I'm having some issues with the Idler arm on the right track. The seal inside the fork is allowing grease to blow...
View ArticleCat 941B Final Drive Pinion Replacement
Hi I am new to this forum. Just wondering if anyone has replace a final drive pinion. I have tracks separated and final drive removed. The drive pinion has 2 gears that are chewed up. It run fine but I...
View ArticleAfter market parts
Need both balance shafts for Cat 3304. Do Costex (CTP) seem to be quality parts? Open to suggestions.
View Articlekomatsu d75s
trans oil level is there someone out there that can tell me how to check it? engine running or not. i paid big bucks "for me" for a manual and it does not say running or not running
View ArticleCan you get a cage for for front assembly of a Kubota SVL75 Skidsteer?
Our new kubota SVL75 Skidsteer does a lot of bush work and tree clearing. Recently a tree branch went through the front window and ticled the operators belly, luckily. Is there a supplier within...
View Article