?? on tracks for a cat 941 track loader????
Hi i was just wondering if anybody knows what is the going price on have a set of tracks rebuilt for my cat 941.By that i mean having new pin/bushing and pad bolts/nuts installed.Sorry the place i get...
View ArticleBad starter for Kamatsu D20s-3
Anyone know where I can get either a rebuilt starter for my old Kamatsu D20s-3 track loader or an armiture and brushes? Solinoid is good. Thanks Tom G
View ArticleLeft side Track Adjustment Grease inlet
The old 931b will not take grease to adjust the track. I know i have seen some threads on grease fitting not taking grease, How to unstop or should i remove the inlet valve? Also if i remove the 4...
View ArticleHyd. Tubing
Hey HEF, The tubing that goes to the lift arm is bent badley, the fitting looks like its welded on, or is it sodered on, its 5/8 d. Also i'am having trouble finding the Hyd. Tubing. I need to redo the...
View Article977l
Looking for pointers, basic failure prone areas of a late 70's unit. Track shoes about 30%, rails are SALT, rollers do not appear to be digging on the rail pin ears, lower guides and rock gaurds are...
View Articlelr622 and 655c Compatible Parts?
I am currently working on a LR622 that has been marked as a 655c. The large outer bearing took a crap because the seal was damage at one time and all the fulid was lost plus they were operating in...
View Article955L Help
Have a cat 955L serial#85j5308 can anyone tell me if it has a d330 or 3304 engine? I need to rebuild the engine where would some good placesto get parts and engine kit? Thanks.
View ArticleJoystick control counterintuitive when backing.
I just purchased my first CTL (Kubota SVL90) for personal use and I have no previous experience on operating these machines. One thing I found quite counterintuitive is that when backing the machine,...
View Articlehoney its me again...bobcat t300 , 2003 model, left track noise
Hi folks, I have a loud squeal coming from the left track hub. We have checked the front idler and feel this area is ok. We have been told that inside the hub there is the hydraulic drive motor and a...
View ArticleNeed help locating hydro filters for deere 855
More specifically trans filters, I need locations and filter numbers if anyone could help out,my first Deere loader, I bought it for a stockpile loader because ut was big and cheap. I would like to...
View ArticleTightening tracks on a 455c
Greetings & Merry Christmas to everyone. This is my first post as a new member. I purchased a 90's models Case 455c a few weeks ago to do field push backs, some general pasture renewals and odds...
View ArticleClik here to view.
lever berings replace
Hi, HEF , I need to replace the bearings in the lever arms, the bottom have a lot of movement, my repair manual is does not have any info on the removal and repair. I have broken the bolts loose and...
View Articlestuck track adjustor? Cat 955
So after my complete go through of my machine, I was all set to do some clearing. In about 90 minutes I got more cleared out then I thought I was gonna get done in a day. it was so awesome until a...
View ArticleClik here to view.
Small cracks
Hello HEF, I have been trying to paint my 931b and have found 3 cracks so far, one is near the top of the bucket close to the hinge. There are 2 at the bottom on each side where the front is attached...
View Article955L, 3304 Arrangment #
On my 955L all I have is the serial #85J5308 on the tag on the side of the motor, which is the same as the track loader tag. I need to get parts for the motor but I need to know the arrangement #, can...
View ArticleBolt on cutting edge segments for 955L?
It's been suggested to me by someone who rebuilds buckets that I could install bolt on segments under the cutting edge and between the teeth of my 955L. I'd have to torch bolt holes in the cutting edge...
View Article955L 13X1 Track adjuster removal
I've been trying to get the track adjuster out of my 955L but I can't get the front idler far enough forward to remove the adjuster. Is there something that stops it from going further forward. I just...
View ArticleGuy's help me pick out a good farm size track loader with 4-1 and teeth
I NEED SOME help from more experienced folk who could help me pick out a good tracked loader for my farm. i need to clear about 2-3 miles of overgrown fence rows, scrub areas, make a road and level out...
View ArticleLine boring IH 175B lower bucket bushes
I uploaded this video for reference if anyone has the same problem of elongated bushes after a long time of abuse this worked well for us, we built this rig pretty cheap compared with getting someone...
View Article?? about renting Cat tools.
Well this spring i want to install new sprockets on my cat 941 track loader.Now i have not call the cat dealer yet. but figured they would want a arm and a leg. But i was wondering if any body in MO or...
View Article