941b cat
I have a 941b cat that runs well and has been working good until today. It stopped going backwards and forwards. Can't see any reaction when put into forward or reverse in any gear. Has lots of oil was...
View ArticleSomething to ponder on....
I was thinking , which has been dangerous at times , in todays economy what would be cheaper to build a 953 A/B or a 955L. My thoughts are the 955 would cost more to build because of the complex...
View Article931B is alive...
Put the new battery in, then luckily a couple guys showed up to ride my MX track and helped me put the seat frame back in. The seat frame is almost worse than the starter! Hopefully I don't have to...
View Article1976 CASE 450 - Can I use any good Hydraulic Fluid? Also Cylinders Leak Some?
I want to change the Hydraulic Fluid on my 1976 Case 450. Ive been using TRAVELLER® Universal Tractor Fluid. Can I use some other Good Universal Fluid? maybe something that will help with leaking...
View ArticleClik here to view.
Lifting arm without power...
Hi, I am a complete newbie at this, so pre-forgive any ignorant questions. Buddy of mine has purchased a few dozers and loaders (all track) to be able to make two completely working machines. Long...
View Article953 tilt cylinder
Cylinder is starting to seep. Reading up on removal procedures I run into 1 possible obstacle: do I need a hydraulic pusher/puller to remove the front and rear pins? I think I can manage the rest and...
View Articleether assist
My 953A has and ether starting assist which uses the throw away cylinders. On the assist assembly is a metal cap with a chain stay that screws on to a small cylindrical compartment on the side. Looks...
View Articleinternational 175b
What would cause an early 70s international to stop working in reverse when it warms up.
View Article941B Steering Pedal Issue
I have a 941B and the right side steering pedal won't recoil when released and is hard to push. It has been doing this for awhile now, but has been parked for a few months and has gotten really bad....
View ArticleGot To Find a CAT 953B - Alomost had one, it got pulled back into service
Hello! I was about to pull the trigger on a 953B, but seller decided to put in back into service and needed it. Really need one... preferably with lower than 10,000 hours around the '92-98 year ranges....
View Article????Cat 951C tracks fit a cat 941 S/N 80H2365???????
I have a Cat 941 with a set of very very worn out track,s. i have a chance to get a very nice used of chains off nitelights cat 951C, but before i drive 2 states over to get them i should better make...
View ArticleCAT 257b track drive motor leaking oil
My track drive motor was working erratically. It wouldn't work, then it would for a little bit, then it would stop again. There is hydraulic fluid dripping from the motor. Could this be something...
View ArticleCase 450 track loader won't start
Normally it starts quickly but not today. I have good fuel flow into injector pump but nothing on high pressure side. Return line is clear also. Any help would be greatly appreciated,
View ArticleWish I had the teeth on the bucket
I need to remove some topsoil/sod so I can build a pad for shop. I have a cat 931B with a backhoe and in hindsight I should have just used the backhoe. I put a smooth cutting edge on the front bucket...
View Article655 john deere
How do I get the pin out of the tracks to replace sprocket , just drive it out or is there a pin holding it in , thanks.
View ArticleTrack makes a squeak like there's something stuck in it?
My 931B is working good but I was loading some clay I dug with the backhoe and sometimes(not always) the left track made a squeaking noise like something was caught in it when going in reverse. I...
View Article655 deere
Is there a good place to order after market gauges for a 655 Deere or just order from Deere ? any good parts places to order parts other than John Deere ? Thanks.
View ArticleJD 655 vs Dresta 175C vs Cat 955L Advice
Hi guys, I think this site is great with a lot of experienced people here and am in need of some information to help make a good decision. I am looking to purchase one of the above mentioned loaders...
View ArticleCat 941 steering linkage
I recently took a look at a 941c , the owner said the left steering pedal when pushed went to floor and just stayed there limo, he seems to think its some type of fork or linkage that broke ? Anyone...
View ArticleClik here to view.
931 Cat track adjuster
Does this mean it needs seals in the track adjuc Attached Images
View Article